Get complete information related to latest Ctpt Unit Scrap Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Ctpt Unit Scrap Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Ctpt Unit Scrap Tenders.
Tender For supply of low voltage fuse without holder for transformer secondary side of non ac lhb type coac hes. gr. 00 500v/25a, sr. 7 item no. 12 f10 confirming to rcf spec no. edts 355 rev. 1. make-siba/ef en/ferraz/eti/siemens/bussmann/schneider/ge/l&t only as per bill of material of rcf spec no. edts 3 55 rev. 1 [ warranty period: 30 months after the date of delivery ]
Tender For corrigendum : supply of item no-1 auto actuated high velocity spray system transformer tr-021 as per atc page no-23 , item no- 2 auto actuated high velocity spray system transformer tr-022 as per atc page no-23 , item no- 3 as per atc page no-23 , item no-4 mandatory spares as per atc page no-23 , item no-5 mandatory spares as per atc page no-23
Tender For supply of 200 va control transformer, 750/415 v ac, 50hz, 1 phase, dry type and air cooled control transformer for the sbc of power car, type ii, as per rdso specification no. rdso/pe/spec/ac/020 3-2020 (rev-0) or latest. transformer should be duly fitted with approved makes 4 amps/1.2 kv fus e link with fuse base for primary and 2 amps/500 volt fuse link with base for secondary with approved make note: 1) firms should attach rdso approval letter for the item along with offer. offer rece ived without rdso approval letter shall be summarily rejected. [ warranty period: 30 months after the da te of delivery ]
Tender For testing and calibration of different electrical equipment related to ht installation (vcb, transformers, starters, motors, protective relay etc.) at chhal ocm , secl, raigarh area . - item description, testing & calibration of protective relay ( idmt/overhead relay, elr, cdg, earth fault relay, no volt relay/master trip relay, under/over voltage relay), testing of 6 nos. 6.6 kv/230v, 25 kva, transformer, 1 no. 1250kva, 33kv/3.3kv transformer and 1 no. 315kva, 3.3kv/440v transformer, this includes magnetizing test, magnetic current test, vector group test, ir/pi test, ratio test, acidity test, as per latest cear field testnote: work also includes prepartion of test report etc., testing of 6.6 kv ht motor, this is include ir/pi test, inductance test asper latest cear flied test, test and calibration of 6.6 kv vacuum circuit breaker panel having 5 nos. panels received from j&k area at chhal ocm sub station and 2 no. field vacuum circuit breaker chhal ocm sub station, 1 no. sf6 circuit breaker dharam sub station, which includes ir test, contact resistance test, close open test, as per latest cear field test, ir/high voltage test of cables, testing & calibration of all other protective/measuring equipments (meggers, lux meter, high voltage detector, multimeter etc.) in mine & surfacenote: work also includes prepartion of sigle line daigram, mine plan, test report etc., test of 6.6 kv overhead lines, which includes ir test of conductor, and post , disc insulator ir test as per latest electricity rule, test of 6.6 kv ht starter panel, which includes ir test, contact resistance test, close open test, as per latest cear field test, total impact of gst for the purpose of ctc
Tender For supply of inhibited mineral insulating oil as per type ii transformer oil of is 335:2018 and to railw ay's requirement as per rdso letter no. ti/psi/insol/policy /19 dt. 26/07/19 with the following additio nal characteristics requirements. 1. lowest cold start energizing temperature 0 degree c . 2. presence of oxidation inhibitor (dbpc-2, di tertiary-butyl-para- cresol) content range -0.25%-0.30% 3. oxidation stability: (a) total acidity neutralization value after oxidation (max) 0.2mg koh/gm. (b) total sludge after oxidation (max) 0.05% by mass. note: rdso's additional requirement no.2 and 3 to be tested in any one of the nabl accredited laboratories and copy of the report to be furnished to consignee by tp i along with their inspection report. [quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitt ed: max 8 lacs ]
Tender For supply of sim (item no.9) for 60kva transformer in lhb ac coaches as per icf drg.no.lwscwac/eog-7-1-003 alt.a, col-iii ( item no.9- 4 nos / set) [ war ranty period: 30 months after the date of delivery ]
Tender For set of gasket for oil circulate joint of transformer as per drg.no. a3/08/el s/ldh/tfp/m-01/alt-1. note: firms, other than mentioned in rdso tc no. elrs/tc/0076, rev.2 must submit rdso approved bill of material (bom) for supply of this item by them. firms not submitting rdso/clw approval will we considered only for developmental order wi th prototype approval by rdso/clw. [ warranty period: 30 months after the date of delivery ]
Tender For supply and installation of single inlet centrifugal fan suitable for 3-phase , 415v ac, along with ducting arrangement for pantry in vande bharat trainsets. specia l note: safety clause must be followed according to annexure-a of dy.cple-ii l.no.rcf/e mp/1 dated.01.04.2025, as per drawing: edts-331, rev. a, corr-1,2 and 3. (type-iii), packing instr uction: alternator,rru, erru &accessories, transformer,bulk inverters , battery, charg er, self priming monoblock pump, inverter, change over control box etc: suitably cove red with biodegradable transparent polythene and packed in wooden cage: bottom fra me to be made of wooden planks 20mm thick &should have support of at least 3 woode n battons of size 100x100mm of suitable length to facilitate lifting by fork lifter. each panel to be packed in wooden cage of suitable dimensions made out of wooden strips o f 20x100mm size. gap between each strip should not be more then 100mm. the material u sed for product packaging shall be eco-friendly.a list should be pasted on each wood en cage showing order no, pl no, description of the item, drg. no/ spec. no ,qty, firm's n ame &address and date of despatch etc. note- 1) firms have option to provide qr code. for linkage of po, the cardboard box shall carry a qr code having details as listed bel ow: a) name of the manufacturer b) purchaseorder number c) pur chaseorder date d) uniqueserial number (or lot number for bulk items) of the manufacturer or e) dateof manufacture f) deliver ychallan no. g) deliverychallan date 2.the qr code shall be as per iso/iec 18004 model2 and the data shall be available as xml using the tags detail ed above. [ warranty period: 30 months after the date of delivery ]